Customer Support
Search:     Advanced search

Module Firmware

Article ID: 1490
Last updated: 01 Oct, 2018
Revision: 48
Views: 13611

Ag Leader CAN-based module updates are included with our display firmware files. To update the majority of your Ag Leader modules you simply need to update your display and the next time your display detects the module it will update the firmware. Included below is the firmware for Ag Leader ISOBUS modules and non-Ag Leader CAN modules.

Ag Leader CAN Modules

Name Version Download Link Release Date Release Notes

Additional Info

Water Management Module 1.6 WMC_4003080_1_6_0_0.fw2 (1.6MB) September 2016 Release Notes  

Ag Leader ISOBUS Modules

Name Version Download Link Release Date Release Notes

Additional Info

Hydraulic Down Force 1.7 WSM_DownForce_1_7_0_0.fw3 (3MB) March 2018 Release Notes
Liquid Rate Control 1.14 WSM_Liquid_1_14.fw3 (6 MB) August 2018 Release Notes
Swath Control 1.1 Liquid_Swath_1_1.fw3 (1 MB) August 2017 N/A
Serial Bridge 1.3 SerialMaster_1_3.fw3 (1.7 MB) September 2015 N/A
Seven (7) Section Auxiliary Input 1.3 AuxInput_1_3.fw3 (2 MB) February 2016 N/A
Ag Leader ISOBUS Reprogramming Tool AgLeaderReprogrammingTool.exe (11 MB) April 2017 N/A

Installation Directions for Ag Leader displays 

  1. Download the appropriate firmware file and place it on a USB storage device.
  2. Navigate to the displays "View Module Firmware" page.
  3. Insert the USB into the display; the "Upgrade From USB" button should now become active.
  4. Press the "Upgrade From USB" button, locate the .fw3 file and highlight it.
  5. Press the green check mark to Accept the file and begin the upgrade process.

Installation Directions for non-Ag Leader displays 

  1. To update an Ag Leader ISOBUS module that is being used with a non-Ag Leader display, download the Ag Leader ISOBUS Reprogramming Tool listed above.
  2. You will also need the Laptop to ISOBUS Interface Kit (PN 4200145) available from the Parts Catalog.
    • Note: PN 4200145 will include a USB to CAN module (a.k.a "CAN Simulator module"). If you already have this module and will utilize it, only purchase an ISO-USB Interface cable (available from the Parts Catalog).
      • The ISO-USB Interface cable will connect to the "CAN" side of the USB to CAN module, and adapt into the vehicles ISOBUS communication line.
  3. Follow the directions in the Ag Leader ISOBUS Reprogramming Tool User Guide.

Non-Ag Leader CAN Modules

NORAC UC5 Boom Height System

Version Download Link Release Date Release Notes
5.2.0.0. E2UC5-5.2.0.0.fw2 (2.2 MB) April 2016 Version 5.2.0.0.

Installation Directions

  1. To update the firmware on the NORAC UC5 system through an Ag Leader display, follow these upgrade instructions.
  2. See the NORAC UC5 Manual for additional information.

Hagie Bridge Module

Version Download Link Release Date Release Notes
1.3 Hagie_Bridge_1.3.fw3 (1.5 MB) August 2016 N/A

Installation Directions for Ag Leader displays 

  1. Download the appropriate firmware file and place it on a USB storage device.
  2. Navigate to the displays "View Module Firmware" page.
  3. Insert the USB into the display; the "Upgrade From USB" button should now become active.
  4. Press the "Upgrade From USB" button, locate the .fw3 file and highlight it.
  5. Press the green check mark to Accept the file and begin the upgrade process.

Installation Directions for non-Ag Leader displays 

  1. To update an Ag Leader ISOBUS module that is being used with a non-Ag Leader display, download the Ag Leader ISOBUS Reprogramming Tool listed above.
  2. You will also need the Laptop to ISOBUS Interface Kit (PN 4200145) available from the Parts Catalog.
    • Note: PN 4200145 will include a USB to CAN module (a.k.a "CAN Simulator module"). If you already have this module and will utilize it, only purchase an ISO-USB Interface cable (available from the Parts Catalog).
      • The ISO-USB Interface cable will connect to the "CAN" side of the USB to CAN module, and adapt into the vehicles ISOBUS communication line.
  3. Follow the directions in the Ag Leader ISOBUS Reprogramming Tool User Guide.

EZ-Boom

Name Version Download Link Release Date
EZ-Toolbox PC Software 2.10 EZ-Toolbox_V210.zip (1 MB) September 2006
EZ-Boom Firmware 1.5.0.0 EZBoom_1.5.0.0.zip (1 MB) February 2010

Installation Directions

  1. Download the EZ-Boom firmware.
  2. Upgrade steps vary based on whether you are using EZ-Boom with the EZ-Guide 500/250 or EZ-Guide Plus.
    • EZ-Guide 500 or 250
      1. The EZ-Boom upgrade is done the same way the lightbar firmware is upgraded. After you download the EZ-Boom firmware, unzip it and save to your USB drive.
      2. Plug the USB drive into the back of the EZ-Guide unit and turn the lightbar on. Wait until the jump drive is recognized and the upgrade process is automatically started.
    • EZ-Guide Plus
      1. First download and install the EZ-Toolbox PC Software listed above, it is required to upgrade EZ-Boom through an EZ-Guide Plus.
      2. To upgrade the firmware on the EZ-Boom, the EZ-Guide Plus will have to be connected to a PC using a serial cable. See these detailed instructions for more information.


Content last reviewed on: 8/30/18
Reviewed by: LM
Attached files
file Ag Leader Firmware Reprogramming Tool UG.pdf (138 kb)
file 4004192-HagieBridge-1_2_0_0.fw3 (1.48 mb)